Often, there are many problems when you need to connect a computer wirelessly to a router or router. And if for this process is used network cable, then there are usually no obstacles. Please note that this connection requires an active Internet connection.
At the same time, it should be understood that even in such simple manipulations, some difficulties and errors may occur, which will result in the device not gaining access to the World Wide Web even when cable Internet is connected via a LAN cable.
In this article, we will look at how you can connect the Internet via cable to your computer or laptop. All manipulations are considered on the example of the operating system Windows 7, but they will also be valid for later versions.
How to connect cable internet to a computer
In order to do this, we need:
- A Wi-fi router that has at least one free LAN cable slot (its color is yellow).
- Network cable. Such a cable, which has a minimum length, is included with the router you purchased. But if a cable with a longer length is needed, then it can be purchased at one of the computer stores.
- PC with network card or connector.
Next, we need to take a network cable, and then connect it at one end to the yellow LAN connector located on the back of the router. It does not matter which of the several connectors the cable is connected to. The other end must be connected to the appropriate connector on the device.
Now check if the indicator lights up, indicating that a computer has been connected to the LAN connector. If so, then you need to look at the computer display. On the notification panel, in the lower right corner, the connection status should be displayed without error marks. If so, then the device is connected to the Internet.
Internet connection without a router
To provide a direct connection from the provider to your PC's network card, you need to connect the cable directly to the port called Ethernet. It is located on the back of the computer.
After that, you should configure a new connection.
Step by step network setup in Windows 7:
- Using the start menu:
- Go to "Control Panel".
- When the window with the panel has opened, you need to go to the "Network Control Center".
- In the column on the left, click on the inscription "Change adapter settings".
- Then, in the folder where all existing connections are located, you should right-click on the Ethernet connection, and then - in the context menu on the inscription "Properties".
- After that, you will need to select the TCP / IPv4 protocol and go to its "Properties" again.
- That's almost all. If you need the connection to be provided via a static IP, then you should check with the provider for the field settings in the window that opens.
- If you need a dynamic IP, then you should not change anything in the protocol properties window. Any settings and field values will be "dictated" by your system in automatic mode. You just need to press the "OK" key, and the Internet is connected to your device via a cable.
We carry the Internet through a cable to a new PC
In a situation where you need to connect the network to a new device, the algorithm will be slightly different. In such a situation, you will need to create and configure a connection from scratch. Initially, you will need to plug the cable directly into your computer's network card.
Now we do the following:
If the manipulations are performed correctly, then in the lower right part of your computer or laptop you will see a symbol indicating the newly created connection.
Read also:
Why is the internet not working? Problem solving
The causes can be varied, and to eliminate each of them, you will need to perform certain actions.
- Check if the internet cable is connected. You should make sure that the cable is actually connected and that it is connected to the correct connector.
- The cable or network card is faulty, or the lan port on the computer is not working. If there are no problems connecting the cable, then you should make sure that the computer is really connected to the network. Pay attention to the indicator on the router or near the connector in the PC. Also, at the bottom of the taskbar, the connection icon will be covered with a red cross. In this situation, it is necessary to repair the network card or troubleshoot the cable.
- The network is not working although the indicator is flashing. In such a situation, you must first install / reinstall the network driver.
- Driver installation completed, but no connection? Go to the control panel, and then to the network and sharing center. If the word "Disabled" is grayed out next to the Ethernet connection, right-click on the connection and then click on "Enable".
- You need to set up a connection. How to do this, you can find above in the article.
- The router is faulty. If the cable is connected to the computer not directly, but through a router, then the malfunction may be caused by lost router settings. Check this by connecting a network cable directly to the device.
- The period paid to the provider has ended. Contact the provider's technical support and check the balance status.
- The connection was blocked by viruses. It is necessary to check the entire system with an antivirus.
Setting up the Internet in Windows XP is not difficult. This applies to both wired and wireless connections. In the first case, the parameters are set in the section "Network connections", which is located in the Control Panel. In the second, everything is done with the loading of drivers if they are not originally present in the system.
Connection setup
If the setup is for a wired connection, then you need to know certain network parameters. But this does not apply to the case when the computer is connected to a Wi-Fi router via a cable. With regard to the wireless network, things are different.
If the laptop comes with pre-installed Wi-Fi, then you just need to download the necessary drivers and connect to your home network. The procedure for the discrete adapter is similar. It is even easier for owners of 3G/4G modems: just download the necessary software, enter the SIM PIN code if required, and activate the connection.
Method 1: Direct wired connection
Open the menu "Start" and click on "Control Panel". There, switch to the classic display view, if such an option is available. Expand element "Network connections".
Several devices can be displayed in the window. Find the one with signed status "Connected", and double click on it. There, select the item with the name "Internet protocolTCP/IP" and open its properties. 
Check the checkboxes for manual input mode, and then specify your network settings. Button "OK" will be confirmation of your actions.
Note: the Internet may not work even with the correct parameters. This is because your connection is set to a network device with a differentMAC address. In this case, you need to call the provider and describe the problem, technical support everything will be fixed in a few minutes.
Method 2: Wired connection via Wi-Fi router
Now let's figure out how to connect the Internet with a cable through a router on Windows XP. In this case, detailed settings are not required, since the device parameters are already set as required. It remains to connect it to a computer or laptop via an Ethernet cable.
Important: two cables are initially suitable for the router: one for power, the second for the Internet. You don't have to touch them. Connect the third one to one of the free numbered sockets, and then insert it into the network adapter on the computer.
When the physical connection is complete, all that remains is to set up the computer for correct operation. Most likely, even this is not required, the Internet will start working immediately. If this does not happen, then follow these steps:
Close the settings window and go to any program that works with the Internet, such as a browser. There you can check the connection status. If the instruction did not work, then the problem is with the router settings.
Method 3: Wireless network
Setting up Wi-Fi in Windows 7, as well as an external modem, is different from a wired connection. First you need to find and install drivers for the device. Usually they are included in the package, they are also available for download from the official website. The shortcut to enable 3G/4G is located on the desktop. Open it, and then click the connect button.
The connected Wi-Fi will be displayed in the tray. Click on its icon, select your home network and enter the access code for it.
Hello, dear subscribers and guests of my blog! In today's issue, I will tell you about the features of setting up the Internet on a mobile phone. A mobile phone is the very first improvised computer tool with which a person can access the Internet.
In order to be able to be online in social networks, read news, use a navigator or check mail, you need to set up an Internet connection on your phone. Not everyone knows how to properly set up the Internet on their phone. Internet setup is divided into two types: automatic and manual. IN this material consider all possible options for connecting a mobile device to the Internet.
How to set up the Internet on the phone automatically?
One of the easiest and fastest ways to connect your phone to the Internet is to order an automatic setup service from your mobile operator. The option to receive settings for accessing the Internet is free for all available Russian operators, and does not depend on the connected tariff plan. To receive automatic settings, you need to call from mobile phone to the call center, and then leave the appropriate application. After some time, the phone will receive automatic settings for the Internet, and the user will need to agree with their installation. To do this, open the message, and then select the "Set Settings" button. This method is one of the most popular to connect your phone to the Internet.
There are cases when, after receiving automatic settings on the phone, the device cannot access the network. In this situation, you will need to perform the following manipulations:
- Make sure that the appropriate tariff for Internet access has been connected.
- make sure it's available Money on your mobile account.
- Make sure that the settings have been installed on the phone, for which you definitely need to click on the "Set settings" button.
- Reboot the device.
Most Android phone models may not support the automatic configuration option for mobile operators. A number of such operators include: MTS, Life and Beeline. If, nevertheless, your device does not connect to the network, then you will need to create the settings yourself. To do this, you need to order settings from your mobile operator, for which you visit the official website from a computer, fill in the required fields and send the settings to your phone. There is also a way to use short numbers, which you need to dial from a mobile phone that you want to connect to the Internet.
For Life operator: dial *123*6#. You can also send an SMS to number 123 with the text "INTERNET".
For Beeline operator: you need to dial the command *110*181#.
For the Megafon operator: you need to send an SMS with the number "1" to the number 5049.
For MTS operator: visit the official website or follow the link http://www.mts.ua/ru/online-services/settings#settings-auto. Thus, the 3G service will be connected.
It is important to know! Many users receive the settings automatically on their phone after the first SIM card connection.
Now let's pay attention to the manual settings for connecting to the Internet on the phone for one of the most popular operator in Russia - MTS.
How to set up the Internet on your phone manually?
Manual way to set up a connection for an MTS operator
The mobile company MTS provides communication services not only in Russia, but also in countries such as Belarus and Ukraine. If the device cannot connect to the Internet by obtaining automatic settings, then the following manipulations should be performed:
1. Go to the main menu on your Android device.
2. Go to the "Settings" menu, and then find the section "Wireless networks" or " Mobile networks».
3. After that, you need to enable the function mobile internet. This can be done by moving the shutter to the right position. If you do not enable this function, you will not be able to connect to the network.
4. After that, a list of mobile networks will be offered. You need to find the appropriate MTS Internet profile or create it yourself. To do this, go to the "Access Points" section, and then select the appropriate profile from the proposed list or click on the option to create a new access point. The screenshot below shows access points for connecting to the Kyivstar mobile network, but these points will be presented in the same way when installing an MTS SIM card.
4. If you need to create an access point manually, then you should click on the above button, and then specify the Name - MTS, Login Username - mts, Password - mts, as well as the address of the connection point or APN: internet.mts.ru. All other parameters remain unchanged.
5. After that, you can start trying to access the Internet from your smartphone. Manual settings for operators such as Beeline and Megafon are almost identical, so there is no need to consider them separately. In order to clarify the address of the access point, you will need to contact the operator.
How to connect 3G connection?
To take advantage high speed internet 3G, you will need to configure your device. At the same time, it is important to pay attention to 3G tariffs and connect the appropriate service, otherwise the use of the Internet will turn into a huge waste.
To set up your phone to connect to a 3G network for operators such as MTS and Life, you must order automatic settings. If for some reason you cannot do this, then you should create an access point manually. To do this, you need to do a number of the following manipulations:
- You must click on the network mode selection panel.
— Select the item GSM/WCDMA.
After that, close the settings window, and then restart the smartphone. After that, you can observe the appearance on the smartphone screen of a high-speed connection using 3G technology.
On some more modern smartphones, only the preferred networks need to be set: 2G, 3G or 4G.
Now the smartphone will automatically connect to the mobile Internet using 3G technology, unless of course there is such a type of coverage in your area.
Features of manual Internet settings from the Life operator
Let us also consider the features of manually setting up an access point to the Internet network of the mobile operator Life. This is a Ukrainian mobile operator that requires special attention to the settings for the Internet. To connect mobile Internet on Life, you must perform the following manipulations:
We go into the settings of the smartphone, after which we select the item “Mobile networks” or “Connections”. It all depends on the phone model and operating system version. In the window that opens, select the "Other networks" section.
In the window that opens, select "Mobile networks".
It is necessary to check the box next to the "Mobile data" item, and then enter the "Access points" section.
After that, the item for creating a new access point is selected.
In the window that opens, scroll down and select two items: Authentication Type or Authentication Type, and Access Point Type or APN Type.
In the first window, you must select the "PAP" mode.
In the window with the name "Access point type" you need to write the text with the name "default", and then click on confirmation.
After that, in the access point menu, you can find a new point, which you need to select.
After that, be sure to restart the phone, and after turning it on, make sure that the data transfer mode function is enabled in the settings. Then you can start using the mobile Internet.
Now, in order to access the Internet from your smartphone, you just need to turn on the corresponding “Mobile Internet” mode.
Summing up today's article "how to set up the Internet on your phone", it remains to add that to access the Internet you will also need to use a special browser that has the same names as for computers. When you open the browser, the home page should automatically load, which indicates the presence of mobile Internet. If there is no Internet, make sure that the phone "catches" the network.
Detailed configuration of the operating system is quite complicated for the average computer user, so errors and difficulties often occur in the process. Especially when it comes to creating an Internet connection. It is not always possible to figure out where the network access settings are located and how to use them. However, reading this article will help clarify most aspects, thereby solving the issue of connecting to the Internet without calling a computer specialist.
internet connection
First you need to understand the network interfaces. There are several connections through which information is transmitted from the user's personal computer to the Internet space:
- Normal ethernet compound. It implies a direct connection of the provider's cable to the computer. Able to pass through a separate router or built-in ADSL modem.
- high speed connection PPPoE, which provides fast data transfer thanks to innovative network technologies.
- Wireless WLAN connection. It requires a router that supports the appropriate wireless interface.
- Connection via portable USB modem. The speed of such a method will depend on the technology that provides data transfer. Today there is 3G and 4G connection.
We will try to explain how to configure all of the above network interfaces. If you already know which way to access the network you will use, then you can skip to a specific section.
Internet connection via Ethernet mode in Windows 10: via network cable (router, modem)
Let's first consider a simple connection to the Internet via an Ethernet port. It is characterized by the fact that does not require login and password for the full use of services. There is only a laid cable from the provider leading to the consumer's apartment.
To start setting up an Ethernet connection, you need to insert the cable connector into the router And connect the latter to a personal computer(it is also possible to connect to a network card without a router). You just need to plug the cable into the socket.
- If the Ethernet connection settings have already been entered into the operating system, then the Internet will instantly work, notifying the user about this with a notification in the taskbar. If nothing happened after inserting the cable, you need to install the driver for the network card or router.
- If a notification appears on the taskbar that the connection was successfully established, but the status " unknown network" or " Limited”, then you should carefully check the settings of the Internet adapter. This usually solves the problem of a non-working connection.
Setting up an Ethernet connection in Windows 10
In Windows 10, you can configure the adapter using the following instructions:
1. First of all, you need to click on the network connection notification and then in the window that appears, select " Network Control Center».
2. In the open window, select the section " Changing the settings of a (network) adapter”, then a window with available network cards opens. Here we point to ethernet adapter, right click and open it " properties«.
In the list that opens, select " IP version 4 and click on it 2 times. In the settings window that appears, check that the mode is set to " Automatic IP connection And addressesDNS". If not, it should be noted. Upon completion, you must confirm the changes with the " Ok».
After all the above steps, the Ethernet connection should definitely work. Otherwise, you need to restart the computer, check the integrity of the network cables and make sure that there are no breakdowns on the side of the Internet provider.
Tip: in case of unsuccessful attempts to set up a network connection, you need to check with the provider about the availability binding by MAC address. If there is such a binding, it is recommended to tell the provider the address of the computer. He will indicate it in his database and the Internet connection will start working.
Setting high speed PPPoE connections in Windows 10
Some ISPs run network cables into customers' homes and then provide a special login And password, required for mandatory connection authorization specific to this high-speed PPPoE connection. To configure it, you need the same practical manipulations as in the case of Ethernet. But with the only difference, which is the need to independently create a connection.
Tip: if the network cable passes through the router, nothing needs to be configured on the personal computer, since all settings are made in the router itself. You just need to insert the cable leading from the modem into the appropriate connector on the computer case. The sequence of actions for creating such a connection is described above.
In the absence of a router, you will have to connect the network cable directly to the computer. This will require knowledge of the login and password given by the provider. If this condition is met, you can proceed to the following instructions.
- To get started, the user needs to open " Network Control Center» after clicking the internet connection icon on the taskbar.
- Then you need " Create a new connection»by entering the section of the same name. Select item " Internet connection” and click the “ Further».
- In the window that appears, select " high speed connection” and click on it with the mouse. After that, the options will appear.
- Now you should enter the username and password provided by the ISP. You can also name the connection with the name of the provider, so as not to get confused. Check the box next to " Remember password". After the actions taken, you need to press the " Connection».
In the case of correctly set parameters, the Internet should work in a few seconds.
- You can view information about an established network connection and manage it on the taskbar by clicking on the corresponding icon.
If you click on the name of the connection, a special menu will open. In it, the user can change the connection settings at his discretion.
Connecting to the Internet via Wi-Fi in Windows 10
If you have a wireless router, connecting to the Internet via Wi-Fi is very fast. It allows you to visit the network from any home device, and also provides complete freedom of movement around the apartment due to the absence of cables. To set it up, you first need to install the appropriate Wi-Fi adapter driver on your computer. Although the Windows 10 system almost always does this automatically. A potential user can only open the list of available networks (WLAN), select the required one and enter the password set on the router. After a few seconds, the computer will connect to the Internet.
- Click on the Internet connections icon on the desktop (bottom right), select the one you need by clicking on it, set the checkbox for the subsequent connection and click " connect«.
Connecting and configuring the Internet via a 3G / 4G modem in Windows 10
It remains only to describe the connection method using a portable modem that supports 3G or 4G communication technology. If you have previously had the experience of installing such a connection on previous versions of the Windows operating system, then there will be no particular difficulties. And for those who are engaged in such an activity for the first time, detailed instructions are given below.
- First you need to insert the modem connector into the USB port of a personal computer. The necessary driver can be installed by itself if the modem manufacturer has provided a corresponding function. Sometimes you need to deal with this issue yourself. For example, find a driver on the manufacturer's website or install from a disk. When connecting the modem, when prompted to install the driver, specify the path of its location, previously downloaded and by inserting the installation disk. If there is no driver for Windows 10, you can try software for previous versions of Windows 7.8 systems.
- After finding the driver and installing it on your computer, you should start setting up the connection. The sequence of actions performed is similar to that which is carried out when creating a high-speed PPPoE connection. Need to open Network Control Center» after clicking the internet connection status on the taskbar.
In a small window that appears, you need to click on " Create a new connection» and select « Internet connection” (this item is the first in the list) and confirm with the button “ Further«.
- Next, select " Switched". It is marked with a landline icon.
- It's time to enter the parameters. This includes information such as number and custom name. This information provided by your ISP, so if you don't have one, you should contact your network service provider directly. The image below shows an example where the services of the Intertelecom provider are used. After filling in the text fields, you must press the "Create" button.
After completing the above steps, the network connection should work. If this does not happen, you need to check the USB modem and the signal reception quality. In some regions, the coverage is not very good and the signal may be constantly cut off, preventing you from working on the Internet. Decide this problem capable of various tricks like building up an antenna and going out into the open.
It is noteworthy that the created connection can be stopped, disabled or edited at your discretion. It can also be removed if the need arises to change the provider. To perform these manipulations, you need to click on the network connection icon on the taskbar and select the required item in the list that appears. You should click on it - to display the control page (it is also available in the computer section " Options» -> « Dialing a number«).
The signal reception status will always be displayed on the taskbar as a small icon. By its appearance, the user is able to determine that in this moment happens with communication. If the icon is blinking, data is being transferred. A crossed line means no signal at all. And if a yellow exclamation mark is displayed next to the icon, then there is a problem. The Internet in this case refuses to work.
Conclusion
If you have established a network connection on a laptop or personal computer with a Wi-Fi beacon, then you can use it as a router, in the article. This allows you to distribute the Internet to all home devices without a wireless router.
As for the occurrence of the most common error " Limited". This notification has a yellow exclamation mark icon and indicates that there is no network connection. Its causes are varied, and if it appeared. This topic will be covered in the next article of the site.
The above instructions for setting up the connection turned out to be voluminous, but divided into sections. Therefore, if you need to create a connection, you need to go to a specific header and start reading. We hope that thanks to the article you will be able to set up a network.
Hello friends! We continue to understand how to set up the Internet and solve various problems in Windows 10. I have already prepared several useful articles on this topic, I will give links below. Well, in this article we will set up the Internet in Windows 10. Let's talk about setting up a regular network connection, a high-speed connection (PPPoE), WiFi networks, and 3G/4G modems. I think the article will be useful to many. Indeed, after upgrading to Windows 10, not everyone can immediately figure out where and what to configure and how to do it. Yes, and there are times when, after upgrading to Windows 10, the Internet simply does not work. Most likely, you just need to reconfigure the connection.
We know that there are different ways to connect our computer to the internet. In this article I will try to talk about setting up basic connections:
- Setting up a normal Ethernet connection. Connecting the cable directly from the provider to the computer, through a router, or an ADSL modem.
- Internet connection via Wi-Fi.
- Internet setup via USB 3G/4G modem.
Now we will take a closer look at setting up an Internet connection through the connections listed above. You should find out what kind of Internet you have, and you can immediately jump to the desired subheading in this article. Let's start with Ethernet - a very popular way to connect to the Internet.
Ethernet: Internet connection in Windows 10 via network cable (router, modem)
Consider first the simplest connection. If your ISP just ran a network cable into your house, and the provider did not provide a username and password to connect to the Internet, then you have a normal Ethernet connection.
In the same way, an Internet connection is configured in Windows 10 through a router, or an ADSL modem.
To set up such a connection, just connect a network cable from the provider (router or ADSL modem) to your computer (laptop), to the network card slot:
If with Ethernet settings everything is fine on the computer (they have not been changed), then the Internet should immediately work (you will understand this by the connection status on the notification panel). If the Internet via a network cable does not work, the computer simply does not respond to connecting the cable, then see. I myself have encountered such a problem.
If the connection appeared, but status Limited, or unidentified network, and the Internet does not work, then you need to check the parameters of the Ethernet adapter.
In Windows 10, this is done like this:
We right-click on the status of the Internet connection, on the notification panel and select the item. Next, click on the item in the new window Change adapter settings.
Right click on the adapter ethernet and choose Properties. Select an item from the list IP version 4 (TCP/IPv4). If the checkbox next to this item is not checked, then be sure to check it, otherwise the Internet will not work. So we selected "IP version 4 (TCP / IPv4)" and press the button Properties.
In a new window, we check that automatic settings for obtaining IP and DNS addresses are set, and click Ok.
The internet should be up and running. If not, then restart your computer. If you still can’t establish a connection, then check the cable connection, if there are any problems on the provider’s side, if the router or ADSL modem through which you are connecting is working normally (unless you have a direct connection to an ISP).
If you are trying to set up an Ethernet connection directly from the provider, and the Internet does not want to work for you, then ask your provider if it binds by MAC address. If it does, then you need to tell the provider the MAC address of the computer. He will prescribe it in his settings, and the Internet will work. Few providers use such a binding, but it happens. How to find out the MAC address in Windows 10 read.
That's all, we figured out this type of connection, then we have a high-speed connection.
If your Internet provider has laid a cable into your house and provided you with a username, password, and possibly some other data for connecting to the Internet that you need to set in your computer settings or Wi-Fi router, then you need to configure High Speed on Windows 10. connection (PPPoE). What are we going to do now. In fact, this is the same as Ethernet, just here the Internet will not work until we create connections.
If your Internet connection goes through a router, a connection is configured on it (PPPoE, L2TP, PPTP), then you do not need to configure anything on your computer. It is enough to connect the network cable from the router to the computer. I talked about setting up such a connection above.
If you connect the cable directly to the computer, and you have a username and password to connect to the Internet, then you need to create a connection.
We open Network and Sharing Center:
Click on the item. Then, select the item Internet connection, and click on the button Further.
In the next window, select the item: High speed (with PPPoE).
Next, set the username and password that your ISP should provide you. Also, you can specify a name for the connection, for example: " High speed connection Beeline". And you can also check the boxes next to the items for saving the password, displaying the password and allowing other users to use this connection. I advise you to check the box next to Remember this password.
Click on the button To plug, and if everything is connected correctly and the parameters are set correctly, a connection will be created and an Internet connection will be established.
You can see and manage this connection by clicking on the Internet icon in the notification bar.
Clicking on the connection will open the menu Dialing a number, where you can connect, delete, or edit connection settings.
Internet connection via Wi-Fi
If you have a Wi-Fi router installed at home, or you want to connect your laptop to the Internet at friends, cafes, etc., then you can use Wi-Fi for this. If you already have a driver installed on your Wi-Fi adapter, and Windows 10 almost always installs it automatically, then all you have to do is open the list of networks available for connection, select the one you need, specify the password (if the network is secure) and you are already connected to the internet.
On this topic, I have already written a detailed article:. I think there should be no problems with connecting to a wireless network.
Setting up the Internet via a 3G / 4G modem in Windows 10
It remains only to consider setting up a connection via a USB 3G, or 4G modem. On a Windows 10 computer, setting up such a connection will practically not differ from.
First of all, we need to connect the modem to the computer and install the driver on our modem. The driver can be downloaded from the modem manufacturer's website, from the Internet provider's website, or simply found on the Internet. Search by modem name and model. Also, the driver can be on the disk bundled with the modem, or on the modem itself. If there is no driver for your modem for the Windows 10 operating system, then try to find it for Windows 8, or even Windows 7. Perhaps it will work.
After you have installed the driver, connect the modem to your computer, and you can start setting up a 3G connection on Windows 10. By the way, everything is almost the same as when setting up a high-speed connection.
We open Network and Sharing Center.
Click on Creating and configuring a new connection or network and choose Internet connection.
And we set the parameters provided by the provider: number, username and password. I showed on the example of the provider Intertelecom. I recommend checking the box next to Remember this password. You can set the name of the connection to be arbitrary. When you fill in all the fields, click on the button Create.
If everything is ok, then a connection will be created and an Internet connection will be established.
If the connection fails, then check all the parameters and the connection of the USB modem. It could also be that you have very poor coverage from your ISP. In such cases, the Internet may not connect at all, or it may work very slowly. How to see what signal level you have, and how to increase it, I wrote. In some cases, if the network is very bad, you need.
You can start the created connection, stop, delete, or edit it by clicking on the Internet connection icon and selecting the created connection.
Internet connection status, always displayed on the notification bar. By clicking on it, you can disconnect from the Internet, or start the desired connection.
And a few more words
No matter how you set up the Internet, you may encounter a popular error "Limited". When the Internet is not working, and next to the connection status is a yellow exclamation mark. We dealt with this problem in .
The article turned out to be large, but it seems to be not confusing. I wanted to fully answer the question posed in the title. I hope you found the information in this article useful for yourself and connected your Windows 10 computer to the Internet.
You can ask questions in the comments. Please read this article carefully before describing your problem. Perhaps the solution has already been written. Also, see links to other articles, there are many useful information on this topic.
Loading...